![]() Graphically, it is very intuitive, and scanning the local network is done instantly, without having to wait at all. Note: QNAP Qfinder Pro is a highly advanced program, even compared to Synology Assistant. ![]() THan you can use QNAP and see what is logged. You can do that by making an allow all rule and set it to log all. Does all work when you disable the firewall If yes you need to find out what ports/service you need to add. ![]() Follow the instructions in the image below. 2eemeli Posts: 99 December 2011 It is very hard to say what firewall rules you would need to add. For example, you can select your QNAP NAS device, then, at the top left of the page, click the Login icon.Īfter you click the Login icon at STEP 2, your browser will automatically open the page with the link for the selected device. The Qfinder Pro will automatically scan and find all your QNAP devices on your local area network. In today’s article I will show you how to use Qfinder Pro to find your QNAP NAS in your local network.ĭownload the latest Qfinder Pro software for your computer from the blue link below.Īfter the Qfinder Pro is installed on your computer, launch it. Qfinder Pro is available for Windows, Mac and Ubuntu 32/64 bit. Once you install the Qfinder Pro, you will see the latest installed OS version, local IP address, MAC address as well as the name of your QNAP device all at a glance. What the Qfinder Pro does is help you automatically find the address of any QNAP device in your local area network. This method requires SSH access to your NAS, but this allows you to cut&paste the output (back to this message thread) if it fails.If you are a QNAP user, whether you have a NAS, a router or a QNAP switch, then one of the best pieces of software you’ll use is the Qfinder Pro. I would recommend following QNAPedia article: Manually Updating Firmware instead. It simply says " Update failed", which isn't very helpful. Unfortunately the WebUI Firmware Upgrade method provides no troubleshooting information for you as to " why" it failed. I am not sure what the problem is really, could it be a hardware issue? I chose manual installation and then chose the firmware image file and again it started uploading the file to the server, but once uploading was finished, I got the same error (update failed) except this time it also asked me to check the firmware version. So, I accessed the admin page by typing the IP address of the server (192.168.100.254) which got me to the first page where you must initialize the sever. It uploaded the image file to the server (I can tell by looking at the status) but when it finished uploading and started to update, it stopped and I got a message saying the Update failed, try updating firmware through web browser admin page. Well, I downloaded the latest firmware image file. I connected the server directly to the PC to try to update the firmware, I thought that might fix the problem. Have you read the Connecting to NAS by Web Browser section of the fine manual?.What happens when you SSH to 192.168.100.5 as " admin"?.What happens when you open in your Web Browser?.What operating system is installed on your PC?.Is your NAS configured to pickup it's IP address via DHCP? (This is the default setting).Please help me to understand what is it I am doing wrong here, When I y=try to do a cloud configuration and input the serial number on the server, I get a response on the web page saying device not found. Qnap Server IP Address 192.168.100.5 (while the IP address that appears briefly in Qfinder is 169.254.100.100) ![]() Using an application to identify the devices connected to the network and obtain their IP adfdresses i was able to get the following information: However, it behaved in the same manner, the device was still not found on the network. I have tried some suggestion from another section of the forum, where I disconnected the HDDs and started the server to see if it can be detected without any HDDs installed. If I attempt to refresh to scan for the server again, I get the same earlier response of No server found on the network. When I attempt to Configure the server using the configuration wizard, I can see the green progress bar building up slowly, but halfway or so throught it just stops and the bar disappears and server also disappears from Qfinder. When I start Qfinder and then turn on the server, it appears briefly on the Qfinder screen, But no action is possible (I can not configure the server nor access it in any way). When I start Qfinder utility, I get a message saying No server was found on the network and asks me to disable my windows firewall (which is already disabled). My PC is already connected to the WIFI router also by LAN connection. installed two 4 TB WD black HDDs, Connected the server to my WIFI Router through LAN connection. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |